Rangemaster RGG60 Guide de l'utilisateur télécharger pdf (Page 11)

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Pressure Testing

The gas pressure can be measured at one of the hotplate

burner injectors. Lift o a burner head. Fit the pressure gauge

to the injector. Turn on and light one of the other hotplate

burners. Turn on and push in the control knob for the burner

with the pressure gauge tted to let gas through.

Turn o the burners. Reassemble burner top, making sure it is

reassembled in the correct way on the burner body.

Fixing the Hob

The hob must be sealed to the work surface to prevent liquid

from entering into the cabinet. A tape seal is supplied with

the hob.

Carefully follow these instructions to correctly apply the

seal: Turn the hob over and place in on a secure, level

surface. Detach the seal from the backing, checking that the

transparent protection still adheres to the seal itself. Carefully

position the seal along the edge of the hob. Take special care

in the corners making sure there are no gaps. The ends of the

strips must t together without overlapping.

If the surface that the hob is to be tted to is tiled or is not

reasonably smooth, additional sealing with a waterproof

silicone sealant may be required.

Turn the hob back the right way up and position it in the

worktop cut-out.

Secure the hob to the worktop using the brackets supplied.

The positioning of the bracket is dependent on the thickness

of the worktop as shown in (Fig.5-4).

Note: Slide the optional sleeve onto the bracket if tting to

thin work surfaces.

Locate the bracket to the slot on the hob base and then

tighten the retaining screw until it is locked to the worktop.

Electrical Connections

This appliance must be installed by a qualied electrician

to comply with the relevant Institute of Electrical

Engineers (I.E.E.) regulations and also the local electricity

supply company requirements.

RNING: THIS APPLIANCE MUST BE EARTHED

Note: All external wiring must comply with the IEE

Regulations for the Electrical Equipment of Buildings.

Connection to the electrical supply can be made with either

a plug and socket, or be permanently wired via a double pole

switch. The hob is supplied with a 3-core cable, 900mm long.

If a replacement cable is tted it must be 250V high

temperature PVC (85°C), 1 mm²

minimum conductor size.

Gas Connection

Before connecting the appliance, check that it is suitable for

your gas and electricity supply. This information is on the data

label xed to the underside of the hotplate. Gas connection

must comply with the relevant standards and regulations in

force.

The gas connection point is towards the rear of the hob. The

inlet union is Rp ½.

The appliance must be connected to the gas supply system

with one of the following:

A rigid steel pipe

The joints of this pipe must consist of threaded ttings

conforming to the standards. The use of seals such as hemp

with suitable cement, or Teon tape, is permitted.

A copper pipe

The joints of this pipe must consist of unions with mechanical

seals.

A exible hose

A hose is not supplied by with the hotplate. Hoses may be

purchased at most builders’ merchants.

The hose should be tted so that both inlet and outlet

connections are vertical so that the hose hangs downwards.

The hose must be in accordance with the relevant standards.

In the UK these are:

For Natural Gas the exible hose must be in accordance with

BS 669.

For LP Gas it should be capable of 50mbar pressure, 70°C

temperature rise and carry a red stripe, band or label.

Safety Information

Ensure that the gas supply pipe is never able to touch

moveable parts of the built-in cabinet (e.g. drawers). It must

not pass through compartments that could be used for

storage purposes.

When using a exible hose, it is essential to comply with the

following instructions:

• No part of the pipe must be able to touch parts

the temperature of which exceeds 75°C

• The pipe must not be pulled or twisted,

throttled or tightly bent.

• It must not come into contact with sharp edges

or corners.

• It must be easy to inspect the entire pipe

length in order to check its state of wear.

• The pipe must be replaced within the date

stamped on the pipe itself.

If in doubt, contact your supplier.

After completing the gas connection check the hotplate is

gas sound with a pressure test.

ArtNo.050-0012 Gas pressure table

Natural Gas LP Gas hotplates

Propane

Butane

20mbar

29mbar

37mbar

Table 5-1

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 19 20

Commentaires sur ces manuels

Pas de commentaire

Rangemaster RGG60 Guide de l'utilisateur Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Plaques chauffantes Rangemaster RGG60